Here’s a quick installation tip: When installing a set of chrome rocker panels; you can place tape along the top edge of the lower rocker panels to be used as a straight line edge before you actually install each piece. This is a quick and easy way to make sure that each piece is installed nice and straight. Best Wishes! Ron Garrigus

INSTALLATION INSTRUCTIONS:

1. VERIFY PARTS:

Please verify that you have received the correct pieces for your vehicle, as each piece should be clearly labeled as to where they should be attached to the vehicle.

2. CLEANING:

This is the most important step of all because if it not done properly, then the pieces will not properly adhere to the surface, resulting in the piece(s) not staying adhered to the surface.

Using a soft rag and “ACETONE” gently wipe the entire surface that needs to be cleaned. Then follow up by using another soft rag and “ALCOHOL” for the final cleaning process. A minimum of 2-3 minutes should be spent for each one of these cleaning processes.

3. FITTING:

Please dry fit each piece by holding it up to the surface. By doing so you will know ahead of time as to where to properly position each piece during the final application process.

4. APPLICATION:

Gently peel off the adhesive backing on the back side of each piece. Then very slowly position the top corners of each piece onto the surface, and by using slight pressure attach each piece to the surface. Be very careful as you only have one chance to properly position each piece into it’s proper place. If you try and lift up the piece to reposition it, you will put a permanent dent into that piece.

5. FINISHING:

Using firm pressure either by a soft rag or a rubber roller, go over each piece to make sure that it has firmly adhered to the surface. Then peel off the protective white coating off each piece to reveal the beautiful finish. You may then use a mild cleaner to remove any fingerprints if you so desire.

___________________________________________________________________________

Our chrome rocker panels quickly attaches over the top of your existing vehicle body!

Our rocker panels are manufactured from the highest quality grade of stainless steel available. You can be assured of a super long lasting and rust-free chrome rocker panels for your vehicle.

Our chrome rocker panels are highly polished to a brilliant chrome finish!

Our chrome rocker panels are made to exactly custom fit your vechicle for an exact fit.

Our chrome rocker panels have already pre-applied the highest grade of 3M adhesive tape available for permanent adhesion.

RECEIVE A 10% DISCOUNT ON ANY SET OF CHROME ROCKER PANELS!
Enter Coupon Code: BLOG10 when placing your order.

Our Grille Guards for the 2006-2010 Honda Ridgeline are very easy to install since the Grille Guard is a 1 PC. welded unit that is already pre-assembled making installation extremely easy. In addition the grille guard is basically an easy bolt on item since it easily bolts to the existing holes that are already in the frame chassis; which means that no-drilling is required. If you know how to use basic hand tools like a socket wrench; then you too can easily this item very easily!

Our Grille Guards are available either in rust free stainless steel that is highly polished to a brilliant chrome finish; or in a highly durable black powder coated finish! Many of our competitors sell the much cheaper in price and quality the chrome plated steel version which will flake off and rust.

Our Grille Guards are a welded 1 piece design for superior strength; unlike our competitors which sell the much cheaper and inferior 3 piece bolt together design!

The small tubing which covers the headlights can be easily removed for either looks, or for any repairs to the headlights!

You can easily install any auxiliary lighting by using any of the pre-drilled holes!

Our Grille Guards are made to exactly custom fit your vehicle without any drilling or modifications. Since the Grille Guard is already pre-assembled; it easily bolts to the existing holes in your frame. All mounting hardware and installation instructions are included. Free factory technical support is also provided. If you know how to operate a socket wrench; then it’s that simple and easy to install!

Fully Guaranteed! Our rust free stainless steel version of Grille Guards comes with a full lifetime warranty. The black powder coated versions carry a (3) year warranty.

MENTION THIS BLOG AND RECEIVE A $15.00 DISCOUNT
ON ANY GRILLE GUARD!
PLEASE USE COUPON CODE: GIFT15

We are asked quite frequently how to properly choose and install a set of chrome rocker panels for their vehicle. Here are just a few things that you need to know before you purchase a set of chrome rocker panels:

1. MATERIAL: For the longest lasting and most durable chrome rocker panels; choose a good grade of stainless steel such as grade 304 Type 2 which has superior rust resistance. If you prefer the highest chrome finish; then choose grade 434; which has a brilliant chrome finish; but it has a slightly less rust resistance. One other less desirable option is to choose a set made from chrome abs; which has a tendency to fade and is less chip resistant.

2. VEHICLE SURFACE: Most chrome rocker panels that are made from stainless steel are designed to properly adhere to most flat surfaces on a vehicle. If your existing rocker panels on your vehicle has a lot of curvature; then we recommend that you choose a set of chrome rocker panels that are made from chrome abs; which will easily contour to most curvatures. Otherwise if these panels were made from stainless steel; then it would most likely not stay adhered to the vehicle surface due too the curvature.

3. ADHESIVE: We recommend that you choose a set of chrome rocker panels that has already pre-applied on the back side of each piece using 3M Redline adhesive tape; which has superior adhesion properties.

INSTALLATION INSTRUCTIONS:

1. VERIFY PARTS:

Please verify that you have received the correct pieces for your vehicle, as each piece should be clearly labeled as to where they should be attached to the vehicle.

2. CLEANING:

This is the most important step of all because if it not done properly, then the pieces will not properly adhere to the surface, resulting in the piece(s) not staying adhered to the surface.

Using a soft rag and “ACETONE” gently wipe the entire surface that needs to be cleaned. Then follow up by using another soft rag and “ALCOHOL” for the final cleaning process. A minimum of 2-3 minutes should be spent for each one of these cleaning processes.

3. FITTING:

Please dry fit each piece by holding it up to the surface. By doing so you will know ahead of time as to where to properly position each piece during the final application process.

4. APPLICATION:

Gently peel off the adhesive backing on the back side of each piece. Then very slowly position the top corners of each piece onto the surface, and by using slight pressure attach each piece to the surface. Be very careful as you only have one chance to properly position each piece into it’s proper place. If you try and lift up the piece to reposition it, you will put a permanent dent into that piece.

5. FINISHING:

Using firm pressure either by a soft rag or a rubber roller, go over each piece to make sure that it has firmly adhered to the surface. Then peel off the protective white coating off each piece to reveal the beautiful finish. You may then use a mild cleaner to remove any fingerprints if you so desire.

___________________________________________________________________________

Our chrome rocker panels quickly attaches over the top of your existing vehicle body!

Our rocker panels are manufactured from the highest quality grade of stainless steel available. You can be assured of a super long lasting and rust-free chrome rocker panels for your vehicle.

Our chrome rocker panels are highly polished to a brilliant chrome finish!

Our chrome rocker panels are made to exactly custom fit your vechicle for an exact fit.

Our chrome rocker panels have already pre-applied the highest grade of 3M adhesive tape available for permanent adhesion.

RECEIVE A 10% DISCOUNT ON ANY SET OF CHROME ROCKER PANELS!
Enter Coupon Code: BLOG10 when placing your order.

2011-Up Ford Superduty Chrome Grille Guard

Our Grille Guards for the 2011-Up Ford Superduty F250/F350/F450/F550 are very easy to install since the Grille Guard is a 1 PC. welded unit that is already pre-assembled making installation extremely easy. In addition the grille guard is basically an easy bolt on item since it easily bolts to the existing holes that are already in the frame chassis; which means that no-drilling is required. If you know how to use basic hand tools like a socket wrench; then you too can easily this item very easily!

Our Grille Guards are available either in rust free stainless steel that is highly polished to a brilliant chrome finish; or in a highly durable black powder coated finish! Many of our competitors sell the much cheaper in price and quality the chrome plated steel version which will flake off and rust.

Our Grille Guards are a welded 1 piece design for superior strength; unlike our competitors which sell the much cheaper and inferior 3 piece bolt together design!

The small tubing which covers the headlights can be easily removed for either looks, or for any repairs to the headlights!

You can easily install any auxiliary lighting by using any of the pre-drilled holes!

Our Grille Guards are made to exactly custom fit your vehicle without any drilling or modifications. Since the Grille Guard is already pre-assembled; it easily bolts to the existing holes in your frame. All mounting hardware and installation instructions are included. Free factory technical support is also provided. If you know how to operate a socket wrench; then it’s that simple and easy to install!

Fully Guaranteed! Our rust free stainless steel version of Grille Guards comes with a full lifetime warranty. The black powder coated versions carry a (3) year warranty.

MENTION THIS BLOG AND RECEIVE A $15.00 DISCOUNT ON A SET OF RUNNING BOARDS!
PLEASE USE COUPON CODE: GIFT15

Our Grille Guards for the 2005-Present Toyota Tacoma are very easy to install since the Grille Guard is a 1 PC. welded unit that is already pre-assembled making installation extremely easy. In addition the grille guard is basically an easy bolt on item since it easily bolts to the existing holes that are already in the frame chassis; which means that no-drilling is required. If you know how to use basic hand tools like a socket wrench; then you too can easily this item very easily!

Our Grille Guards are available either in rust free stainless steel that is highly polished to a brilliant chrome finish; or in a highly durable black powder coated finish! Many of our competitors sell the much cheaper in price and quality the chrome plated steel version which will flake off and rust.

Our Grille Guards are a welded 1 piece design for superior strength; unlike our competitors which sell the much cheaper and inferior 3 piece bolt together design!

The small tubing which covers the headlights can be easily removed for either looks, or for any repairs to the headlights!

You can easily install any auxiliary lighting by using any of the pre-drilled holes!

Our Grille Guards are made to exactly custom fit your vehicle without any drilling or modifications. Since the Grille Guard is already pre-assembled; it easily bolts to the existing holes in your frame. All mounting hardware and installation instructions are included. Free factory technical support is also provided. If you know how to operate a socket wrench; then it’s that simple and easy to install!

Fully Guaranteed! Our rust free stainless steel version of Grille Guards comes with a full lifetime warranty. The black powder coated versions carry a (3) year warranty.

MENTION THIS BLOG AND RECEIVE A SPECIAL DISCOUNT ON ANY GRILLE GUARD!